Community Profile

photo

M.Mohsin Siraj


Mehran University of Engineering and Technology Jamshoro Pakistan

自 2009 起处于活动状态

Followers: 0   Following: 0

联系

I am an Electronic engineer, right now i am working for a Research and Development Organization...
Professional Interests: Control systems, instrumentation, digital signal processing, automation and robotics

统计数据

All
  • Personal Best Downloads Level 2
  • First Review
  • 5-Star Galaxy Level 3
  • First Submission

查看徽章

Feeds

排序方式：

提问


How can I convert .fis fuzzy toolbox file to verilog? Thanks.
Hi, How can I convert .fis fuzzy toolbox file to verilog? Thanks. Regards,

6 years 前 | 0 个回答 | 0

0

个回答

提问


Transfer function of higher order
Dear all, I need to input a transfer function of the form shown below: G(s) = 1/{((s+1)^10)*((s+3)^10)} I have two ...

11 years 前 | 2 个回答 | 0

2

个回答

已回答
hinfnorm command
Thanks for your answer. But now consider the following simple first order descriptor system a = x1 ...

12 years 前 | 0

已回答
hinfnorm command
Thanks, how can i confirm that the bode and sigma plots and norm does consider the descriptor systems? Also I read in one of th...

12 years 前 | 0

已回答
hinfnorm command
Thank you so much for your detailed answers.... One thing, are 'bode' or 'sigma' and 'norm' defined for descriptor systems as w...

12 years 前 | 0

已回答
hinfnorm command
I have MATLAB 7.12.0 R2011a.

12 years 前 | 0

已回答
hinfnorm command
the norm command as follows: norm(sys,inf) gives the h infinity norm of 3.1974e-014.

12 years 前 | 0

已回答
hinfnorm command
Sorry for the typo... B = [4; 2; 8.718; 7.071] That's the correct B.

12 years 前 | 0

已回答
hinfnorm command
for example, the system below: A = [-1 0 0 0; 0 -2 0 0;0 0 -0.4172 -0.07477;0 0 -0.1495 -0.6489]; B = [4;2;3 8.718...

12 years 前 | 0

提问


hinfnorm command
Hello I am using the command 'hinfnorm' to calculate the infinity norm of a descriptor linear system described by a ltisys comm...

12 years 前 | 16 个回答 | 0

16

个回答

提问


Using LFT of two SISO systems yields system with no input/no ouput
Hey guys I am using an 'lft' command to connect two SISO systems say sys1 and sys2, syntax is N = lft(sys1,sys2); now the out...

12 years 前 | 0 个回答 | 0

0

个回答

已提交


DAQ Through Parallel Port
A simple software to acquire and send data using Parallel Port

15 years 前 | 1 次下载 |

已提交


NI-DAQ Card Data Acquisition
Software for acquiring and saving data from a NI-DAQ Card.

15 years 前 | 10 次下载 |

已提交


controller Design
GUI Software for controller design via PID and Statefeedback appraoch.

15 years 前 | 3 次下载 |

已提交


Structural Vibration Control System
Simulation of structural vibration control system using semi actively controlled MR Dampers.

15 years 前 | 6 次下载 |